Reptile Rooms and set-ups. Lets see them!!

[gko reptiles]

I just recently took some pictures of my reptile room. I will post the pictures tomorrow. I just wanted to start a post to see everyones racks, tanks, whole rooms, etc. I know my gecko room has had about three make-overs. Well, Lets see them everyone.

Phillip Hemingway and Christine Schorr
GKO Reptiles

 

[Jeremy Letkey]

Here are a few older pics. It has changed some since. The Small racks are now doubled up to the ceiling, not to mention all are full. lol
It will also be changing again soon. Maybe I'll take some pics along the way.

 

[SupaHypeGex]

racks

my racks, nothing like what Jeremy has but then again If I had that many racks my wife would kill me

 

[LeoGeckos]

here it is

 

[Marc118]

For those of you using tops on the bins how do you ventilate?

 

[ExcessiveHerps]

Anyone have thier room as crowded as me?

 

[PaulSage]

Xavier, your big turtle tub set-up is awesome. I can't wait until my Reeve's are big enough to warrant building one!

 

[John N]

Joe, looks like you'r cat is eyeing out you'r leos lol.

 

[ExcessiveHerps]

Xavier, your big turtle tub set-up is awesome. I can't wait until my Reeve's are big enough to warrant building one!

Yep I like it got
9'' Female Belize Slider
1.1'' Rio Grande Cooter females 9'' male 6''
one unsexed 4 inch possible male suwannee river cooter
its a 300 gallon rubbermaid stock tank

 

[LeoGeckos]

Yeah my cat would love to "play" with my leos

 

[eyelids]

Yeah my cat would love to "play" with my leos

I can say the same for my cats. Anyways, here's my modest setup and I'm sure the heat tape isn't supposed to go on the outside, but we couldn't get it to lay flat otherwise...

 

[Kimjorg]

holes for ventilation

To make ventilation holes in the sterilite tubs all you have to do is get a simple sautering iron and melt holes in the side of them. It only takes like 6 holes on each side of the tub and is very easy to do. Hope that helps!

 

[boutiquegecko]

I drilled mine, does it make a difference how you get the holes in the sides?

 

[Russ S]

I drilled mine, does it make a difference how you get the holes in the sides?

not at all

 

[sbord_tom]

Nice floor Letkey:main_yes:

 

[wilomn]

The only real difference between drilling and using a soldering iron, that I've seen, is with the drill you can leave behind a little twist of plastic that can be pretty sharp. Melting holes leaves no sharp parts.

 

[PaulSage]

I've been meaning to take some pictures of my "Reptile Room" for a while and only managed to get one decent one before the battery crapped out.

Anyway, these are my gecko breeding racks for the leos and fat tails. There's a few rat snakes in the bottom row of the sweater box racks right now though. I'll try to remember to take some more pics later.

(it's not really that dark in there - I think it's either the lights interfering w/ the camera, or because the battery was dying)

 

[gko reptiles]

I said I would post my pictures so here they are. The room has changed about 4 times now. One last change to go... We are getting animal plastics and boaphile racks to cover the entire wall where the 55 gallon tank is from top to bottom. The tank, of course, is being moved.

 

[gko reptiles]

Here are the two main racks up close.

 

[eyelids]

Nice you're going to be happy with your new racks. Paul, I love it. Clean and simple.